PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2,
and active low reset control for PHY GEN1.

Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset.
Add dw_hdmi_phy_gen1_reset function for PHY GEN1.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com

HDMI1.4b specification section 6.5.3:
Source shall only send GCPs with non-zero CD to sinks
that indicate support for Deep Color.

DW HDMI GCP default enabled, but only transmit CD
and do not handle AVMUTE, PP norDefault_Phase (yet).
Disable Auto GCP when 24-bit color for sinks that not support Deep Color.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78fa41e4fb3d3d53354034bc221fcf870dbac617.1649989179.git.Sandor.yu@nxp.com

i.MX8MPlus (v2.13a) has verified need the workaround to clear the
overflow with one iteration.
Only i.MX6Q(v1.30a) need the workaround with 4 iterations,
the others versions later than v1.3a have been identified as needing
the workaround with a single iteration.

Default enable the workaround with one iteration for all versions
later than v1.30a.

Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/561951005a85574dcdd108e5d6a3a87df930ea3d.1649989179.git.Sandor.yu@nxp.com

If panel_bridge_attach() happens after DRM device registration, the
created connector will not be registered by the DRM core anymore. Fix
this by registering it explicitly in such case.

This fixes the following issue observed on Samsung Exynos4210-based Trats
board with a DSI panel (the panel driver is registered after the Exynos DRM
component device is bound):

$ ./modetest -c -Mexynos
could not get connector 56: No such file or directory
Segmentation fault

While touching this, move the connector reset() call also under the DRM
device registered check, because otherwise it is not really needed.

Fixes: 934aef88 ("drm: bridge: panel: Reset the connector state pointer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419091422.4255-1-m.szyprowski@samsung.com

Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.

Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419142453.48839-1-biju.das.jz@bp.renesas.com

Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.

This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.

Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.

Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de

Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org

To make debugging easier, convert driver to regmap. Implement read and write
regmap tables for known registers, keep all known register readable and mark
those which are obviously read-only as not writeable.

Use common I2C regmap for the I2C configuration, implement custom regmap bus
for DSI configuration. The later is mandatory as this chip requires one extra
byte set to read access length between register address and data.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220403171004.368464-1-marex@denx.de

"hdmi-connector.yaml" bindings defines an optional property
"ddc-en-gpios" for a single gpio to enable DDC operation.

Usually this controls +5V power on the HDMI connector.
This +5V may also be needed for HPD.

This was not reflected in code but is needed to make the CI20
board work.

Now, the driver activates the ddc gpio after probe and
deactivates after remove so it is "almost on".

But only if this driver is loaded (and not e.g. blacklisted
as module).

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/3607e924b7c0cf0be956c0d49894be1442dbda41.1649330171.git.hns@goldelico.com

The module owner = THIS_MODULE is set by I2C core, drop duplicate assignment.

Fixes: 8dde6f74 ("drm: bridge: icn6211: Add I2C configuration support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220401113317.7033-1-marex@denx.de

Fix copy-paste error, module exit function should be marked with __exit
instead of __init.

Fixes: 8dde6f74 ("drm: bridge: icn6211: Add I2C configuration support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406014250.902187-1-marex@denx.de


Reviewed-by: Robert Foss <robert.foss@linaro.org>

The datasheet for this bridge is not available, the PLL behavior has been
inferred from [1] and [2] and by analyzing the DPI pixel clock with scope.
After further testing with other displays and different DSI data lane count,
it turns out the P-factor is not 1/2^N divider, but rather only 1/N divider.
It also turns out the input into the PLL seem to be ByteClock instead of DSI
HS clock.

Rework the P-factor calculation such that the PLL calculation code handles
P-factor from 1..32 with P-factors above 16 must be even. In case P-factor
is even, enable built-in 1:2 divider and program P-factor/2 to PLL_REF_DIV,
otherwise configure only the P-factor into PLL_REF_DIV register.

Switch the PLL factor calculation from kHz to Hz to maintain precision.

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c
[2] https://github.com/tdjastrzebski/ICN6211-Configurator



Fixes: f30cf0ec ("drm: bridge: icn6211: Add generic DSI-to-DPI PLL configuration")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220402004118.897014-1-marex@denx.de

Since this driver has been changed to use the resource managed
devm_drm_of_get_bridge() to get bridge from ->attach(), it's
unnecessary to call drm_of_panel_bridge_remove() to remove the
bridge from ->detach().  So, let's drop the drm_of_panel_bridge_remove()
function call.  As nwl_dsi_bridge_detach() only calls
drm_of_panel_bridge_remove(), it can also be dropped.

Cc: Robert Foss <robert.foss@linaro.org>
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220401015828.2959505-1-victor.liu@nxp.com

devm_drm_of_get_bridge is capable of looking up the downstream
bridge and panel and trying to add a panel bridge if the panel
is found.

Replace explicit finding calls with devm_drm_of_get_bridge.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-4-jagan@amarulasolutions.com

devm_drm_of_get_bridge is capable of looking up the downstream
bridge and panel and trying to add a panel bridge if the panel
is found.

Replace explicit finding calls with devm_drm_of_get_bridge.

Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-2-jagan@amarulasolutions.com

This reverts commit c206c7fa.

In order to avoid any probe ordering issues, the I2C based downstream
bridge drivers now register and attach the DSI devices at the probe
instead of doing it on drm_bridge_function.attach().

Examples of those commits are:

commit <6ef7ee48> ("drm/bridge: sn65dsi83: Register and attach our
DSI device at probe")
commit <d89078c3> ("drm/bridge: lt8912b: Register and attach our DSI
device at probe")
commit <864c49a3> ("drm/bridge: adv7511: Register and attach our DSI
device at probe")

dw-mipi-dsi has panel or bridge finding code based on previous downstream
bridges, so revert the same and make the panel or bridge funding in host
attach as before.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-1-jagan@amarulasolutions.com

Implement .atomic_get_input_bus_fmts callback, which sets up
the input (scanout-engine-end) formats, so that those formats
can then be used in pipeline format negotiation between this
bridge and the scanout engine.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331153923.14314-2-marex@denx.de

Use the atomic version of the enable/disable operations to continue the
transition to the atomic API. This will be needed to access the mode
from the atomic state.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331153923.14314-1-marex@denx.de

In rare cases, the bridge may not start up correctly, which usually
leads to no display output. In case this happens, warn about it in
the kernel log.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213022648.495895-1-marex@denx.de

Read out the Vendor/Chip/Version ID registers from the chip before
performing any configuration, and validate that the registers have
correct values. This is mostly a simple test whether DSI register
access does work, since that tends to be broken on various bridges.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-12-marex@denx.de

Rename and inline macro ICN6211_DSI() into function chipone_writeb()
to keep all function names lower-case. No functional change.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-11-marex@denx.de

The ICN6211 chip starts in I2C configuration mode after cold boot.
Implement support for configuring the chip via I2C in addition to
the current DSI LP command mode configuration support. The later
seems to be available only on chips which have additional MCU on
the panel/bridge board which preconfigures the ICN6211, while the
I2C configuration mode added by this patch does not require any
such MCU.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-10-marex@denx.de

Implement .atomic_get_input_bus_fmts callback, which sets up the
input (DSI-end) format, and that format can then be used in pipeline
format negotiation between the DSI-end of this bridge and the other
component closer to the scanout engine.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-9-marex@denx.de

Both example code [1], [2] as well as one provided by custom panel vendor
set register SYS_CTRL_1 to 0x88. What exactly does the value mean is unknown
due to unavailable datasheet. Align this register value with example code.

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c
[2] https://github.com/tdjastrzebski/ICN6211-Configurator



Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-8-marex@denx.de

The chip is capable of swapping DPI RGB channels. The driver currently
does not implement support for this functionality. Write the MIPI_PN_SWAP
register to 0 to assure the color swap is disabled.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-7-marex@denx.de

The DSI burst mode is more energy efficient than the DSI sync pulse mode,
make use of the burst mode since the chip supports it as well. Disable the
generation of EoT packet, the chip ignores it, so no point in emitting it.
Enable transmission of data in LP mode, otherwise register read via DSI
does not work with this chip.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-6-marex@denx.de

The chip contains fractional PLL, however the driver currently hard-codes
one specific PLL setting. Implement generic PLL parameter calculation code,
so any DPI panel with arbitrary pixel clock can be attached to this bridge.

The datasheet for this bridge is not available, the PLL behavior has been
inferred from [1] and [2] and by analyzing the DPI pixel clock with scope.
The PLL limits might be wrong, but at least the calculated values match all
the example code available. This is better than one hard-coded pixel clock
value anyway.

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c
[2] https://github.com/tdjastrzebski/ICN6211-Configurator



Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-5-marex@denx.de

The driver currently hard-codes HS/VS polarity to active-low and DE to
active-high, which is not correct for a lot of supported DPI panels.
Add the missing mode flag handling for HS/VS/DE polarity.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-4-marex@denx.de

The HFP_HSW_HBP_HI register must be programmed with 2 LSbits of each
Horizontal Front Porch/Sync/Back Porch. Currently the driver programs
this register to 0, which breaks displays with either value above 255.

The HFP_MIN register must be set to the same value as HFP_LI, otherwise
there is visible image distortion, usually in the form of missing lines
at the bottom of the panel.

Fix this by correctly programming the HFP_HSW_HBP_HI and HFP_MIN registers.

Acked-by: Maxime Ripard <maxime@cerno.tech>
Fixes: ce517f18 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-3-marex@denx.de

The chip register layout has nothing to do with MIPI DCS, the registers
incorrectly marked as MIPI DCS in the driver are regular chip registers
often with completely different function.

Fill in the actual register names and bits from [1] and [2] and add the
entire register layout, since the documentation for this chip is hard to
come by.

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c
[2] https://github.com/tdjastrzebski/ICN6211-Configurator



Acked-by: Maxime Ripard <maxime@cerno.tech>
Fixes: ce517f18 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-2-marex@denx.de

Trigger hotplug event with drm_kms_helper_hotplug_event might fail if the
connector state pointer is NULL.

BUG observed in exynos dsi driver where drm_bridge_attach is trying to
register a connector in panel_bridge before the hotplug event is triggered.

WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/drm_atomic_state_helper.c:494 drm_atomic_helper_connector_duplicate_state+0x94/0x9c
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 5.16.0-rc1-00009-g704b1dbfa4c2 #11058
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c0110b30>] (unwind_backtrace) from [<c010c618>] (show_stack+0x10/0x14)
[<c010c618>] (show_stack) from [<c0b657d4>] (dump_stack_lvl+0x58/0x70)
[<c0b657d4>] (dump_stack_lvl) from [<c01261dc>] (__warn+0xd0/0x134)
[<c01261dc>] (__warn) from [<c0b5f628>] (warn_slowpath_fmt+0x5c/0xb4)
[<c0b5f628>] (warn_slowpath_fmt) from [<c064bce4>] (drm_atomic_helper_connector_duplicate_state+0x94/0x9c)
[<c064bce4>] (drm_atomic_helper_connector_duplicate_state) from [<c0666b64>] (drm_atomic_get_connector_state+0xd4/0x190)
[<c0666b64>] (drm_atomic_get_connector_state) from [<c0667928>] (__drm_atomic_helper_set_config+0x314/0x368)
[<c0667928>] (__drm_atomic_helper_set_config) from [<c067e628>] (drm_client_modeset_commit_atomic+0x170/0x278)
[<c067e628>] (drm_client_modeset_commit_atomic) from [<c067e800>] (drm_client_modeset_commit_locked+0x60/0x1c8)
[<c067e800>] (drm_client_modeset_commit_locked) from [<c067e98c>] (drm_client_modeset_commit+0x24/0x40)
[<c067e98c>] (drm_client_modeset_commit) from [<c06509c0>] (drm_fb_helper_set_par+0xb8/0xf8)
[<c06509c0>] (drm_fb_helper_set_par) from [<c05b86d0>] (fbcon_init+0x2c0/0x518)
[<c05b86d0>] (fbcon_init) from [<c060636c>] (visual_init+0xc0/0x108)
[<c060636c>] (visual_init) from [<c06085e4>] (do_bind_con_driver+0x1b8/0x3a4)
[<c06085e4>] (do_bind_con_driver) from [<c0608b40>] (do_take_over_console+0x13c/0x1e8)
[<c0608b40>] (do_take_over_console) from [<c05b6854>] (do_fbcon_takeover+0x78/0xd8)
[<c05b6854>] (do_fbcon_takeover) from [<c05b1154>] (register_framebuffer+0x208/0x2e0)
[<c05b1154>] (register_framebuffer) from [<c064ead0>] (__drm_fb_helper_initial_config_and_unlock+0x400/0x63c)
[<c064ead0>] (__drm_fb_helper_initial_config_and_unlock) from [<c063a718>] (drm_kms_helper_hotplug_event+0x24/0x30)
[<c063a718>] (drm_kms_helper_hotplug_event) from [<c068f668>] (exynos_dsi_host_attach+0x174/0x1fc)
[<c068f668>] (exynos_dsi_host_attach) from [<c0699354>] (s6e8aa0_probe+0x1b4/0x218)

So reset the atomic state for a given connector by freeing the state pointer
and allocate a new empty state object. This can be done using connector
funcs->reset helper and has to be done before the hotplug even calls.

This patch calls the connector->funcs->reset in panel_bridge_attach.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303163654.3381470-3-jagan@amarulasolutions.com

Replace the manual panel handling code by a drm panel_bridge via
devm_drm_of_get_bridge().

Adding panel_bridge handling,

- Drops drm_connector and related operations as drm_bridge_attach
  creates connector during attachment.

- Drops panel pointer and panel healpers.

This simplifies the driver and allows all components in the display
pipeline to be treated as bridges.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303163654.3381470-2-jagan@amarulasolutions.com

The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Add support for the
DSI-to-DPI mode.

This requires skipping most of the (e)DP initialization code, which is
currently a large part of this driver, hence it is better to have far
simpler separate tc_dpi_bridge_funcs and their implementation.

The configuration of DPI output is also much simpler. The configuration
of the DSI input is rather similar to the other TC bridge chips.

The Pixel PLL in DPI output mode does not have the 65..150 MHz limitation
imposed on the (e)DP output mode, so this limitation is skipped to permit
operating panels with far slower pixel clock, even below 9 MHz. This mode
of operation of the PLL is valid and tested.

The detection of bridge mode is now added into tc_probe_bridge_mode(),
where in case a DPI panel is found on port@1 endpoint@1, the mode is
assumed to be DSI-to-DPI. If (e)DP is detected on port@2, the mode is
assumed to be DPI-to-(e)DP.

The DSI-to-(e)DP mode is not supported due to lack of proper hardware,
but this would be some sort of mix between the two aforementioned modes.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-12-marex@denx.de

The tc_set_video_mode() sets up both common and (e)DP video mode settings of
the bridge chip. Split the function into tc_set_common_video_mode() to set
the common settings and tc_set_edp_video_mode() to set the (e)DP specific
settings. No functional change.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-11-marex@denx.de

The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. It is possible to find out the mode in which the
bridge should be operated by testing connected endpoints in DT.

Port allocation:
port@0 - DSI input
port@1 - DPI input/output
port@2 - eDP output

Possible connections:
DPI -> port@1 -> port@2 -> eDP :: [port@0 is not connected]
DSI -> port@0 -> port@2 -> eDP :: [port@1 is not connected]
DSI -> port@0 -> port@1 -> DPI :: [port@2 is not connected]

Add function to determine the bridge mode based on connected endpoints.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-10-marex@denx.de

The bridge ops are specific to the bridge configuration, move them
into tc_probe_edp_bridge_endpoint() to permit cleaner addition of
DSI-to-DPI mode. No functional change.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-9-marex@denx.de

This bit of code is (e)DP and aux I2C link specific, move it into
tc_aux_link_setup() to permit cleaner addition of DSI-to-DPI mode.
No functional change.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-8-marex@denx.de

The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de

Implement .atomic_check callback which prevents user space from setting
unsupported mode. The tc_edp_common_atomic_check() variant is already
prepared for DSI-to-DPI mode addition, which has different frequency
limits.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-6-marex@denx.de

Use the atomic version of the enable/disable operations to continue the
transition to the atomic API. This will be needed to access the mode
from the atomic state.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-5-marex@denx.de