According to Synopsys support channel, each region of HSA, HBP and HFP must
have minimum number of 10 bytes where constant 4 bytes are for HSS or HSE
and 6 bytes are for blanking packet(header + CRC).  Hence, the below table
comes in.

+------------+----------+-------+
| data lanes | min lbcc | bytes |
+------------+----------+-------+
|     1      |    10    |  1*10 |
+------------+----------+-------+
|     2      |    5     |  2*5  |
+------------+----------+-------+
|     3      |    4     |  3*4  |
+------------+----------+-------+
|     4      |    3     |  4*3  |
+------------+----------+-------+

Implement the minimum lbcc numbers to make sure that the values programmed
into DSI_VID_HSA_TIME and DSI_VID_HBP_TIME registers meet the minimum
number requirement.  For DSI_VID_HLINE_TIME register, it seems that the
value programmed should be based on mode->htotal as-is, instead of sum up
HSA, HBP, HFP and HDISPLAY.

This helps the case where Raydium RM67191 DSI panel is connected, since
it's video timing for hsync length is only 2 pixels and without this patch
the programmed value for DSI_VID_HSA_TIME is only 2 with 4 data lanes.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-7-victor.liu@nxp.com

To get better accuration, use pixel clock rate to calculate lbcc instead of
lane_mbps since the pixel clock rate is in KHz while lane_mbps is in MHz.
Without this, distorted image can be seen on a HDMI monitor connected with
i.MX93 11x11 EVK through ADV7535 DSI to HDMI bridge in 1920x1080p@60 video
mode.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-6-victor.liu@nxp.com

Vendor drivers may need to fixup mode due to pixel clock tree limitation,
so introduce the ->mode_fixup() callcack to struct dw_mipi_dsi_plat_data
and call it at atomic check stage if available.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-5-victor.liu@nxp.com

The DATAEN_ACTIVE_LOW bit in DSI_DPI_CFG_POL register is set to zero,
so set the DRM_BUS_FLAG_DE_HIGH flag in input_bus_cfg.flags.  It appears
that the DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE flag also makes sense, so
set it in input_bus_cfg.flags too.  With this patch, the flags set by
drm_atomic_bridge_propagate_bus_flags() are overridden (see comment in
that function) in case any downstream bridges propagates invalid flags
to this bridge.  A real problematic case is to connect a RM67191 MIPI
DSI panel whose driver sets DRM_BUS_FLAG_DE_LOW and
DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE bus flags.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-4-victor.liu@nxp.com

Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data
so that vendor drivers can implement specific methods to get input bus
formats for Synopsys DW MIPI DSI.

While at it, implement a generic callback for ->atomic_get_input_bus_fmts(),
where we try to get the input bus formats through pdata->get_input_bus_fmts()
first.  If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED,
which matches the default behavior if ->atomic_get_input_bus_fmts() is not
implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-3-victor.liu@nxp.com

Add dw_mipi_dsi_get_bridge() helper so that it can be used by vendor
drivers which implement vendor specific extensions to Synopsys DW MIPI DSI.

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-2-victor.liu@nxp.com

As per spec, it is allowed to pulse the HPD signal to indicate that the
EDID information has changed. Some monitors do this when they wake up
from standby or are enabled. When the HPD goes low the adv7511 is
reset and the outputs are disabled which might cause the monitor to
go to standby again. To avoid this we ignore the HPD pin for the
first few seconds after enabling the output. On the other hand,
adv7535 require to enable HPD Override bit for proper HPD.

Add hpd_override_enable variable to struct adv7511_chip_info to handle
this scenario.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-9-biju.das.jz@bp.renesas.com

The ADV7511 needs link configuration whereas ADV75{33,35} does not need
it. Add a variable link_config to struct adv7511_chip_info to handle
this difference.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-8-biju.das.jz@bp.renesas.com

The ADV7533 and ADV7535 have DSI support. Add a variable has_dsi to
struct adv7511_chip_info for handling configuration related to DSI.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-7-biju.das.jz@bp.renesas.com

The ADV7533 and ADV7535 have an offset(0x70) for the CEC register map
compared to ADV7511. Add the reg_cec_offset variable to struct
adv7511_chip_info to handle this difference and drop the reg_cec_offset
variable from struct adv7511.

This will avoid assigning reg_cec_offset based on chip type and also
testing for multiple chip types by calling adv7533_patch_cec_registers().

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-6-biju.das.jz@bp.renesas.com

The ADV7511 has 5 power supplies compared to 7 that of ADV75{33,35}. Add
supply_names and num_supplies variables to struct adv7511_chip_info to
handle this difference.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-5-biju.das.jz@bp.renesas.com

The ADV7533 supports a maximum lane clock of 800MHz whereas it is 891MHz
for ADV7535. Add max_lane_freq_khz variable to struct adv7511_chip_info to
handle this difference.

While at it, drop the unused local variable max_lane_freq.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-4-biju.das.jz@bp.renesas.com

The ADV7533 supports a maximum pixel clock of 80MHz whereas it is 148.5MHz
for ADV7535. Add max_mode_clock_khz variable to struct adv7511_chip_info to
handle this difference.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-3-biju.das.jz@bp.renesas.com

Add struct adv7511_chip_info to handle hw differences between various
chips rather checking against the 'type' variable in various places.
Replace 'adv->type'->'info->type' by moving variable 'type' from
struct adv7511 to struct adv7511_chip_info and add adv7511_chip_info as
device data for both OF and ID tables instead of the device type.

Simplify the probe() by replacing of_device_get_match_data() and ID lookup
for retrieving match data with i2c_get_match_data().

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830142358.275459-2-biju.das.jz@bp.renesas.com

Fix flickering of the pinephone's XDB599 panel that happens after
resume.

Extend the delay after issuing the command to exit sleep mode from 60 to
120 msec as per the controller's specification.

Introduce a 120 msec delay after issuing the command to enter sleep
mode. This is needed in order for the controller to reliably finalize
the sleep in sequence before switching of power supply.

In contrast to the JH057N panel, the XBD599 panel does not require a 20
msec delay after initialization and exiting sleep mode. Therefore, move
the delay into the already existing device specific initialization
function.

The XDB599 does not require a 20 msec delay between the SETBGP and
SETVCOM commands. Therefore, remove the delay from the device specific
initialization function.

Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Cc: Ondrej Jirman <megi@xff.cz>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213123238.76889-2-frank@oltmanns.dev

Switching to a different reset sequence, enabling IOVCC before enabling
VCC.

There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.

This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).

Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev

The plane's atomic_check returns -EINVAL if the CRTC has not been
set. This is the case for disabled planes, for which atomic_check
should return 0. For disabled planes, it also omits the mandatory
call to drm_atomic_helper_check_plane_state().

Replace the test with the boiler-plate code that first invokes
drm_atomic_helper_check_plane_state() and then tests for the plane
to be visible. Return early for non-visible planes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: d51f9fbd ("drm/ssd130x: Store the HW buffer in the driver-private CRTC state")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009141018.11291-7-tzimmermann@suse.de

Replace Martin, who has left GE.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921104751.56544-2-ian.ray@ge.com

Migrate away from custom EDID parsing and validity checks.

Note:  This is a follow-up to the original RFC by Jani [1].  The first
submission in this series should have been marked v2.

[1] https://patchwork.freedesktop.org/patch/msgid/20230901102400.552254-1-jani.nikula@intel.com



Co-developed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921104751.56544-1-ian.ray@ge.com

Use:
  - ivpu_bo_vaddr(bo) instead of bo->kvaddr
  - ivpu_bo_size(bo) instead of bo->base.size

This is a preparation for switch to a drm_gem_shmem_object as a base for
ivpu_bo, where:
  - bo->kvaddr becomes bo->base.vaddr
  - bo->base.size becomes bo->base.base.size

Using ivpu_bo_vaddr() and ivpu_bo_size() increases the readability of
the code.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901094957.168898-9-stanislaw.gruszka@linux.intel.com

We need to check if a link is non-NULL before trying to delete it.

Fixes: 61df9ca2 ("drm/simpledrm: Add support for multiple "power-domains"")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Janne Grunau <j@jannau.net>
Cc: Eric Curtin <ecurtin@redhat.com>
Cc: Neal Gompa <neal@gompa.dev>
Cc: Sven Peter <sven@svenpeter.dev>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20231011143230.1107731-1-thierry.reding@gmail.com

Correct spelling of "beginning".

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230930221428.18463-2-rdunlap@infradead.org

The functions drm_framebuffer_plane_{width,height} and
fb_plane_{width,height} do exactly the same job of its
equivalents drm_format_info_plane_{width,height} from drm_fourcc.

The only reason to have these functions on drm_framebuffer
would be if they would added a abstraction layer to call it just
passing a drm_framebuffer pointer and the desired plane index,
which is not the case, where these functions actually implements
just part of it. In the actual implementation, every call to both
drm_framebuffer_plane_{width,height} and fb_plane_{width,height} should
pass some drm_framebuffer attribute, which is the same as calling the
drm_format_info_plane_{width,height} functions.

The drm_format_info_pane_{width,height} functions are much more
consistent in both its implementation and its location on code. The
kind of calculation that they do is intrinsically derivated from the
drm_format_info struct and has not to do with drm_framebuffer, except
by the potential motivation described above, which is still not a good
justification to have drm_framebuffer functions to calculate it.

So, replace each drm_framebuffer_plane_{width,height} and
fb_plane_{width,height} call to drm_format_info_plane_{width,height}
and remove them.

Signed-off-by: Carlos Eduardo Gallo Filho <gcarlos@disroot.org>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926141519.9315-3-gcarlos@disroot.org

The drm_format_info_plane_{height,width} functions was implemented using
regular division for the plane size calculation, which cause issues [1][2]
when used on contexts where the dimensions are misaligned with relation
to the subsampling factors. So, replace the regular division by the
DIV_ROUND_UP macro.

This allows these functions to be used in more drivers, making further
work to bring more core presence on them possible.

[1] http://patchwork.freedesktop.org/patch/msgid/20170321181218.10042-3-ville.syrjala@linux.intel.com
[2] https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-2-imre.deak@intel.com



Signed-off-by: Carlos Eduardo Gallo Filho <gcarlos@disroot.org>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926141519.9315-2-gcarlos@disroot.org

Rename the fbdev mmap helper fb_pgprotect() to pgprot_framebuffer().
The helper sets VMA page-access flags for framebuffers in device I/O
memory.

Also clean up the helper's parameters and return value. Instead of
the VMA instance, pass the individial parameters separately: existing
page-access flags, the VMAs start and end addresses and the offset
in the underlying device memory rsp file. Return the new page-access
flags. These changes align pgprot_framebuffer() with other pgprot_()
functions.

v4:
	* fix commit message (Christophe)
v3:
	* rename fb_pgprotect() to pgprot_framebuffer() (Arnd)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922080636.26762-3-tzimmermann@suse.de

Only PowerPC's fb_pgprotect() needs the file argument, although
the implementation in either phys_mem_access_prot() or
pci_phys_mem_access_prot() does not use it. Pass NULL to the internal
helper in preparation of further updates. A later patch will remove
the file parameter from fb_pgprotect().

While at it, replace the shift operation with PHYS_PFN().

v5:
	* state function names in commit description (Javier)

Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922080636.26762-2-tzimmermann@suse.de

It's confusing for a function to return NULL and ERR_PTR()-encoded error
codes on failure. Make sure we only ever return the latter since that's
what callers already expect.

Reported-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZSVuVcqdGfGtQIQj@orome.fritz.box

UBSAN reports an invalid load for bool, as the iosys_map is read
later without being initialized. Zero-initialize it to avoid this.

Reported-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901115910.701518-2-cyndis@kapsi.fi

Original implementation over allocates the memory size for the
contexts list. The size of memory for the contexts list is based
on the number of iommu groups specified in the device tree.

Fixes: 8aa5bcb6 ("gpu: host1x: Add context device management code")
Signed-off-by: Johnny Liu <johnliu@nvidia.com>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901115910.701518-1-cyndis@kapsi.fi

Support sharded syncpoint interrupts on Tegra234+. This feature
allows specifying one of eight interrupt lines for each syncpoint
to lower processing latency of syncpoint threshold
interrupts.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901114008.672433-1-cyndis@kapsi.fi

With the previous CDMA stop fix, executing runtime PM ops around
system suspend now makes channel submissions work after system
suspend, so do that.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901111510.663401-3-cyndis@kapsi.fi

Before going into suspend, wait all CDMA to go idle and stop it.
This will ensure no channel is still active while we enter
suspend, and ensures the driver doesn't think that CDMA is still
active when coming back from suspend (as HW state has been reset).

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901111510.663401-2-cyndis@kapsi.fi

Add locking around channel allocation to avoid race conditions.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901111510.663401-1-cyndis@kapsi.fi

When converting from int to string, we must allow for up to 10-chars (2147483647).

Fixes the following W=1 kernel build warning(s):

 drivers/gpu/drm/tegra/hub.c: In function ‘tegra_display_hub_probe’:
 drivers/gpu/drm/tegra/hub.c:1106:47: warning: ‘%u’ directive output may be truncated writing between 1 and 10 bytes into a region of size 4 [-Wformat-truncation=]
 drivers/gpu/drm/tegra/hub.c:1106:42: note: directive argument in the range [0, 4294967294]
 drivers/gpu/drm/tegra/hub.c:1106:17: note: ‘snprintf’ output between 6 and 15 bytes into a destination of size 8

Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230824073710.2677348-16-lee@kernel.org

Commit 776dc384 ("drm/tegra: Move subdevice infrastructure to host1x")
removed the implementation but not the declaration.

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230809030226.3412-1-yuehaibing@huawei.com

else is not generally useful after return

Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230626143331.640454-2-suijingfeng@loongson.cn

Implement the oob_hotplug_event() callback. Translate it to the HPD
notification sent to the HPD bridge in the chain.

Reviewed-by: Janne Grunau <j@jannau.net>
Link: https://lore.kernel.org/r/20231009174048.2695981-4-dmitry.baryshkov@linaro.org


Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009174048.2695981-4-dmitry.baryshkov@linaro.org

In some cases the bridge drivers would like to receive hotplug events
even in the case new status is equal to the old status. In the DP case
this is used to deliver "attention" messages to the DP host. Stop
filtering the events in the drm_bridge_connector_hpd_cb() and let
drivers decide whether they would like to receive the event or not.

Reviewed-by: Janne Grunau <j@jannau.net>
Link: https://lore.kernel.org/r/20231009174048.2695981-3-dmitry.baryshkov@linaro.org


Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009174048.2695981-3-dmitry.baryshkov@linaro.org

In some implementations, such as the Qualcomm platforms, the display
driver has no way to query the current HPD state and as such it's
impossible to distinguish between disconnect and attention events.

Add a parameter to drm_connector_oob_hotplug_event() to pass the HPD
state.

Also push the test for unchanged state in the displayport altmode driver
into the i915 driver, to allow other drivers to act upon each update.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009174048.2695981-2-dmitry.baryshkov@linaro.org


Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009174048.2695981-2-dmitry.baryshkov@linaro.org

Updating drm-misc-next to the state of Linux v6.6-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>